Refrigerator ice maker water line hookup, plumb the fridge
How to install a refrigerator water line? Be sure to put a gasket seal between the valve and the T-fitting. If you already have an installed cold water valve behind your refrigerator, all you will need to hook up your fridge to water is some flexible plastic water tubing going from the wall valve to the fridge water inlet valve.
Required Materials for this Project Avoid last-minute shopping refrigerator ice maker water line hookup by having all your materials ready ahead of time.
You may have to drill a hole through the wall or the floor if needed to get the other end to the water valve. Family HandymanWhirlpool ].
Another option would be to not use the icemaker in the refrigerator, and replace it with a countertop icemaker:. It has a tiny shutoff valve that uses a sharp pointed metal rod to pierce the outer wall of the pipe when screwed inward. We recommend more permanent valves and copper tubing for better water flow and reduced risk of leaks, which can cause extensive damage.
Now the refrigerator is connected. If you have a choice, select a vertical pipe not horizontal, as sediment can enter the fridge water refrigerator ice maker water line hookup easier 2 Types of Water Valves can be used Saddle Valve or In Wall Water Valve for Refrigerator Water Line Step 2 — You will be drilling a hole into the cold water pipe so turn off the main water supply to your complete house.
6 Suggested Answers
If you need help replacing the filter, here is a guide to replace a refrigerator batting eyelashes flirting tips filter.
Set the ice maker to the "on" position as indicated in your specific model.
Turn off email alerts. Part 3 of 3.
By Cynthia Gomez SAVE While old refrigerators often lacked a water line, you may find that most new ones come with a connector and hose to run a water line, much like you would from your home's laundry hookups to a washing machine.
Thread water line hook up ice maker nut on the tubing end onto the compression connector soldered to the cold-water supply line. If not, you will need to run a line to the nearest cold water pipe, which is probably in the floor below your kitchen.
Delivery Options see all Delivery Options. They can often make ice on their own, and higher end models also dispense cold and hot water.
Turn the main water on to your home.
Alternative connections These photos show alternative ways to connect to the cold water pipe. Discard the first two or three batches of ice to flush the system. Avoid over-tightening; you can crush the copper pipe if you apply too much pressure. You'll receive email and Feed alerts when new items arrive.
Attach the nut to the refrigerator valve.
You will need to locate where the cold water pipe is, drill to access it, and install a water valve and flexible water tubing. If you want the refrigerator to make ice, you typically turn a knob or push a lever on the ice maker in the freezer.
Are there any better alternatives? To begin, shut off the water at the main valve, then open the sink faucet and another lower level faucet to drain the pipe.
Do not over tighten. Total cost, bout bucks, cause you micro pump will need a plug in. This usually will take an hour and a half or so to complete.
Shut off the water valve and attach the open end of tubing to the valve on your refrigerator. Put the end of the water line into the empty bucket.
3 Ways to Install an Ice Maker - wikiHow
The refrigerator automatically gets the right amount of water needed to make ice cubes and continues to make ice cubes in batches until you turn or shut the ice maker to the off position. Tapping the Cold Water Line 1 Shut off the main water supply to your home. Your fridge should now have a perfectly working ice maker and water dispenser!
Depending on brand of refrigerator, you will need certain types of water filters. Figure 6 to 8 ft. There's a problem loading this menu right now. I accidently held my finger on the mic of my phone in a couple of spots. You'll need quarter-inch copper tubing that measures the length between your wall hookup and the hookup location on the back of your refrigerator, plus about 7 feet to allow for moving the fridge.
Then you back out the rod and water flows through a tiny hole into the tubing. This extra tubing will allow you to move the refrigerator away from the wall for cleaning and servicing without disconnecting the water supply.
We offer appliance parts and repair services on our website Normally the compression fittings come with the fridge. Shut off the water supply.
Add Your Answer
Drill a hole either through the cabinet wall separating the space under the sink and the refrigerator or in the basement ceiling up to the refrigerator. Below is step-by-step instructions for installing a water line to your fridge. To straighten coiled tubing not the entire rollhave a partner hold the end of the tube flat on the floor, then push the roll against the floor while unrolling to the length you need to go through the cabinets.
Start the line from the refrigerator but do not install it onto the fridge yet. You should have cold water very shortly. We removed the drainpipes to clearly show this project.
Refrigerator ice maker water line installation
Purpose Refrigerators need water lines so that they can get the water needed to make ice and dispense water. It's not hard doing this so don't stress out about it.
An hour project of drilling and running flexible hose is well worth the pleasure of ice on demand. If you have a water dispenser on your fridge, dispense about a gallon of water and spill it down the kitchen sink drain.
Now snake the tubing in backward, starting at the fridge so the coiled portion remains there. Then decide which one of three refrigerator water line connection options you will use: It takes patience, but you can hook a water line up to your refrigerator on your own.
Shop by category
Step 9 — Now the other end of your water tubing needs to be connected to the refrigerator. The folks at GE Appliances recommend using a vertical pipe, if available. Part 2 of 3. If you have CPVC plastic or steel pipes, add tee fittings made of the same material.
Step 6 — Get out the plastic water tubing from your fridge water line kit. Tahun Yang lalu My Instagram: